Built-in battery

　Low voltage rail electric flat car is 36V low voltage rail powered electric flat car, its working principle is through the ground control voltage reduction system, the 380V power supply (three-phase or single-phase) voltage down to 36V safety voltage. The power is fed to the conductive rail (the conductive rail is also used as a walking track for the flat car) and the low voltage power is sent to the step-up transformer on the flat car through the conductive device of the flat car, which is stepped up to 380V to drive the three-phase or single-phase capacitor motor and drive the flat car.

The ladle truck is also known as a steel handling truck. It is a kind of electric flat car specially developed for steelmaking plants to transport high temperature ladles. Because of the high temperature of the steel and slag, the use of ordinary transfer electric In order to avoid accidents such as steel and slag bursting and causing burns to employees, the manufacturer has developed a ladle transfer vehicle, which can be operated remotely. The ladle transfer vehicle can be operated remotely, with free control of the running speed, and running on rails to avoid steel splashes and high temperature burns and to ensure the health of employees.

A billet truck is a truck that is used to transfer billets. The billet is the product obtained after casting of the steel trained in the steelmaking furnace.

The BTL rail electric carriage is powered by a cable, which is placed on the ground. When using, first check that there are no obstacles on the track and that the line position is at a certain distance from the track so that the wheels do not run over the cable when the carriage is running.

Chain release repair: One of the causes could be that the chain is too loose, please adjust the chain tightness. The reason for this is that the sprocket, chain and flywheel are not on the same plane. Repair as follows: Remove the sprocket and check if the sprocket is deformed or worn. Please repair and replace the sprocket. Pay attention to the position of the flywheel and rear wheel for deviation, if there is deviation, please make adjustment. If the flywheel is worn, replace it. Deformed or worn chain, replace chain. Please note that the direction of the joints of the chain links is opposite to the direction of movement of the chain links.

The advantages of the KPD low-voltage rail electric flat car are that it does not use cables, safe and reliable, not afraid of scalding, not afraid of breaking, not hindering cross transport, easy to remote control and automation, can be driven on curves and loops, appropriate to increase the number of step-down transformers, not limited by the distance of flat car operation, the transport layout of the factory plant has great convenience.

As the mileage is related to the car load weight, road condition, starting times, braking times, wind direction, wind speed, temperature, tyre pressure, etc., so you should ride with your feet first when starting and twist the harmony handle during using. When riding on bridges, uphill, against the wind and heavy loads, you must use your foot to help you avoid damaging the battery and affecting the life of the battery range; Charge often: when using lead-acid batteries, you should get into the habit of charging your electric flat cart on the same day. No matter how far you use your battery powered transfer trolley each day, you should always charge it fully. Don’t wait until the charge is depleted to avoid shortening the battery life due to deep discharge.

KPD low voltage rail electric flat car is suitable for small tonnage, medium distance, cross operation with other vehicles operating environment. The utility model is suitable for workpiece handlers who need hydraulic lifting when operating at a distance of 70m or more, need to increase the number of transformers to compensate for track pressure drop, have high requirements for track laying and need insulated track.
Low-voltage rail electric flatcars require insulated tracks and insulated rails. Suitable for transporting heavy loads of more than 50 t. The electric flatcars have a high starting torque and are relatively stable, they are also suitable for transporting workpieces of high height that do not move.

The towed rail transport vehicle is sometimes called the manual transfer car or motorless transfer trolley. As a non-power transfer cart running on the rail, it can be manually powered or towed by other cars. In addition, the roller carrier, fence and other appliances are optional as required. If you need a rail transport vehicle made with special dimensions, or for a particular application, we can satisfy your needs.

Battery Transfer Cart Bogie Wagon Trolley Handling Equipment Customized 3 ton battery rail truck, battery power supply, color customization, running sound and light alarm, emergency brake switch, wired handle and wireless remote control two control modes, customer own money, transfer personalized customized integrated houses, customized tabletop specifications.
Battery Power Motorized Rail Cart is a kind of electric railroad transportation vehicle in the factory, which solves the problem of product transportation between the spans of the factory. Battery Power Motorized Rail Cart is also known as straddle car, trolley, and electric flat car. It has the advantages of simple structure, convenient use, easy maintenance, large carrying capacity and less pollution. It is widely used in machine manufacturing and metallurgical factories, as the interior of the workshop to cooperate with the crane to transport heavy objects across the span.

heavy load construction bridge rail transfer cart Customized 6-ton rail pallet truck, powered by 48v battery, working principle: powered by battery, driven by electric motor, the flat car is equipped with on-board control buttons, which can control the forward, backward and stop of the flat car. The flat car is braked by an electromagnetic brake motor, the brake is stable, reliable, safe to use, and convenient for maintenance.

Steel Mill Heavy Loads Applied Material Transfer Flat Carriage.The customized 3 ton trackless transfer platform truck is mainly used to transport metal parts and processed parts in the workshop. Transfer before workshop and warehouse. The countertop is customized, the power is battery-powered, and battery-powered is not limited by distance.

The custom-made large-tonnage trolley for transporting coils solves the problem of coil replacement. Because the coil is heavy, hoisting is not safe, and the trolley is used at will instead of hoisting for transportation.

A trackless transport vehicle that handles molds, realizes the straight-line transportation from the mold warehouse to the press, and is engaged in realizing quick mold change. The load capacity is 16 tons, the ground is required to be a hardened pavement, and the size of the table top is customized.

BWP series transfer cart is trackless type which can running on the cement floor or steel plate ground. This type transfer cart has not limited of rails and can 360° turning around.

rail transfer car for production line 25 ton.Customized rail car, the color is bright yellow and gray overall, large platform car, flat table top, can be customized according to the actual situation, flat car load 8 tons, pre-layed track, rail car is convenient to use, battery-powered, environmental protection, can also be used The way of rail power supply. There is a remote control handle on the car to control the operation of the car. The rail car runs smoothly, safely and quickly. It is the first choice for transporting materials.

rail transfer car for materials, Battery rail car, the battery uses a maintenance-free lead-acid battery pack, which has a large capacity and can be used for eight hours on a single charge. It has its own charging device and has an online charging function. The principle is to provide east flow through the battery, and drive the flat car to walk through the motor. The material to be transported is also relatively large on the load-bearing beam, and the table top can be customized, and the safety factor is high.

rail transfer car for handling heavy material, remote control rail transfer car, used in the construction of new plant, the turntable and rail car are used together to move heavy workpieces and run in the workshop. Employees use the remote control to control the operation of the rail car. There are threaded holes to facilitate the installation of workpieces on the table.

Rail transfer car in steel industry, rail transport car has been widely used by many companies, this is a more used transfer car, the advantage of rail car is very convenient. The power of the transfer car comes from the battery. The internal battery allows the flat car to run smoothly. The operation mode, handle and remote control can control the forward and backward of the flat car and ensure the safety of the operator. The battery can also ensure that no pollution occurs during operation, and it can be used for a long time on a single charge.

rail transfer car metal industry using, steel rail car, used to transport cast steel parts in the workshop, with channel steel bracket installed on the car, which can be easily and quickly pulled out for lifting, convenient for unloading, customized table size, load 10 tons, battery Power is supplied, and the remote control controls the operation of the flat car.

rail transfer car for manufacturing industry，automated truck with a load capacity of 35 tons. It is suitable for processing and manufacturing and can handle heavier materials. There are 13 stops on the truck, with a weighing system and wireless communication, which can fully realize automatic control. The control mode can be a handle + remote control mode, which is safer and adopts electromagnetic brake.

rail transfer car pricelist，rail transfer car pricelist, rail car has a wide range of applications, it can be used in different work situations, so it is in great demand in the market, before applying rail car, we need to lay the track on the road first, and its power supply method is also There are many types, which can be provided by batteries or rails, etc. It is convenient to transfer materials easily and quickly in painting workshops, quarries, warehouses, workshops, and multiple workshops.

electric transfer car for foundry industry，the transfer truck can load 10 tons of boring, which can be customized according to different requirements of customers. The table on the transfer truck is insulated, and the insulation voltage ranges from 145kv to 1050kv. The frame is a steel plate welded structure, suitable for epoxy floors, hardened cement, etc. Level the ground. The power supply mode is that the battery provides power to run the entire flat car. It can replace forklifts, cranes and flat cars with high safety factor.

electric transfer car for mold workshop using，customized trackless transfer vehicle, this vehicle is a mold transfer vehicle customized by the customer. The customer is mainly operating CNC machine tools and accessories. The customized trackless vehicle is mainly used to transport molds and plastic products, with a heavy load of 30 tons. , The table top is also customized, and the speed is 20m/min. It can run smoothly when used in the workshop.

electric transfer car for tunnel construction，The electric transfer flat car can be customized, and the table top can be customized according to the actual situation of the customer. This trackless car is based on customer requirements. It has a load of 20 tons and transports raw materials. The flat car is powered by a battery. There are also many options for the battery. The flat car has a remote control handle that can control the flat car from a certain distance to improve safety.

electric transfer car for manufacturing industry,The maximum load of the trackless transfer flat car is 20 tons, the table size is 7000*3000*650, the load and the table size can be customized according to customer needs, suitable for various manufacturing manufacturers. The transfer truck can transport all kinds of equipment. The customized transfer truck mainly transports a pressure device. Since there is no crane in the workshop and there are too many turns, it uses a trackless flat car.

coil transfer cart for the transport of coils 30 ton，Coil transfer car, with a load of 30 tons, large-capacity load, can be used for the transfer of coils and steel rims. The transfer flat car is safe and convenient, and can replace part of the lifting and unloading, and the transfer flat car does not limit the distance, whether it is indoor or outdoor. Can realize the homework, very convenient.

electric transfer car for handling heavy material–Trackless handling flat car, customized products, can be used to carry abrasive tools, realize the linear transportation of abrasive tools from the warehouse to the press, so as to achieve the effect of rapid mold change, can carry heavier raw materials, the table can be customized, and there are urgent problems on the flat car The stop button, and equipped with the handle of the car, safe and convenient.

electric transfer car precast concrete workshop using—The customer is processing and manufacturing raw materials, purchasing our company’s transfer truck, and transferring it in the factory workshop. Because the road surface in the workshop has been hardened and it is a concrete pavement, so the purchase is a trackless transfer truck. The table size is customized by the Genjun customer. The power supply method It adopts battery power supply, and the transfer vehicle is equipped with a remote control handle, which can be started and stopped at any time.

Factory equipment transfer electric transfer vehicle–The customer is a high-tech enterprise that is engaged in electronic aluminum foil. The new energy trackless transfer vehicle purchased by our company has a load of 5 tons. The table top is customized according to customer requirements. It is battery-powered and is safe and environmentally friendly. The transfer truck is mainly used for transfer in the factory workshop and used for the transfer before the equipment.

Customers mainly produce various types of batteries. After more company comparisons, they finally purchased our company’s trackless transfer vehicle. This project is used for high-precision machinery and equipment. The trackless vehicle has a high platform and a slide board designed on the upper surface. Because of the need for finishing, the four corners contain fixed legs. The power supply is battery-powered, and the tabletop is customized according to customer requirements.

The customer is engaged in the processing and manufacturing of metal products, and purchased the transfer truck, mainly for the transfer of steel coils. Because the use of trackless flat cars is safe, the previous lifting and unloading are abandoned, and the trackless truck is used to work outdoors, whether it is a workshop or an outdoor , Can be easily reached, very convenient.

The steel coil motorised transfer flat wagon
is equipped with V-shaped and rollers on the electric coil transfer cart to protect the stability of the coil. The distance of the roller can be adjusted according to the diameter of the coil. The V-shaped support and roller can also be removed from the cart for other purposes. cargo freight. The steel coil motorised rail transfer flat wagon was developed to greatly reduce the material handling requirements of cranes and forklifts, while providing fast, safe and smooth material and product transportation through manufacturing facilities.

Customers mainly operate concrete machinery, construction machinery and equipment. They purchase transfer trucks mainly for transfer in finished goods workshops. Maintenance-free batteries are used for power supply. Battery trackless flat cars are flexible and convenient, and can be transported safely and efficiently. Stop when encountering people and objects, sound and light alarm, etc.

The customer is a manufacturer of purifier equipment. The customer purchases the transfer truck mainly for the transfer of materials, equipment and parts inside and outside the workshop. The flat truck weighs 10 tons, and the table top is customized according to customer requirements. The battery power supply method is adopted. Not limited by distance, it can run for 4 hours at full load.

electric transfer car for steel mill,The customer is mainly making machinery and equipment. This is an exported trolley car, which is used in a steel plant. The transfer car uses a battery power supply, a charging voltage of 380v, a dead weight of about 2.3 tons, and a load of 40 tons. Forklift holes are reserved on the transfer truck.

electric transfer car for non-woven fabric,The customer is dealing in non-woven fabrics and craft products. This transfer car is a new energy trackless transfer car.The transfer car weighs 5 tons. The transfer car is powered by a battery.this transfer car meas is custom, so the tabletop equipped with a V-type frame.

The platform can be customized with a remote-controlled rail car. The platform weighs 5 tons. The platform can be customized according to customer needs. The platform is battery-powered and has a remote control handle that can control the start and stop of the platform at any time.

The trackless transfer vehicle used to transport steel in the factory. The flat vehicle weighs 20 tons. The project is mainly to transport some structural parts of steel or some profiles in the transfer workshop to the spray booth or the drying room. It uses a trackless transfer vehicle, battery-powered, and can be used continuously for four to five hours when it is fully loaded.

The battery-powered trackless coiled material handling vehicle has a large capacity load and can load 40 tons of materials. The project is mainly to transport aluminum coils and aluminum plates. A tooling rack is installed on the table. The tooling rack can not be removed at the same time. Proceed to transport aluminum plates. The battery-powered method used by the flat car is convenient and not limited by the distance.

The large-capacity coil rail car, the flat car weighs 20 tons, and the load is heavy. There are a lot of coils on the customer site, and the single piece is small in size. The weight is up to the original. The customer considers: one is unsafe, the other is , Intelligent single-room transfer, the efficiency is relatively low, the most important thing is that the transfer cannot be completed across the workshop, so after the ditch is passed, the customer uses the rail transfer to solve this problem.

Battery-powered automated railcars. This project is an automated transportation process that is jointly completed with customers. The belt conveyor transports materials, the platform truck waits at the receiving point, the belt conveyor sends the materials to the platform truck, and the cart senses the materials. After that, it runs automatically.

The trackless platform car with hydraulic lifting, the flat car weighs 1 ton, the customer buys this flat car to transfer and unload parts, the platform car table is customized, and the battery power supply is used for power supply. The battery power supply is more convenient and independent of distance. limits.

It is used to transport battery flat cars in the workshop. The customer produces auto parts. The flat car weighs 10 tons. The flat car is purchased for the transfer of metal parts in the workshop. The platform car uses battery power supply. Operation mode: wired + wireless , It is more convenient and safe.

A portable test car that can rotate battery power in multiple directions. The flat car weighs 1 ton. The customer needs to mount other systems in the later period, so the communication interface is reserved in advance. The flat car can climb 5 degrees and stop when encountering obstacles. There is an emergency stop button, which can be rotated in multiple directions, and 360-degree rotation is not a problem.

The railcar used to transport steel in the factory. The maximum load of the flat car is 8 tons. It is exported to Indonesia. The customer is in the foundry industry. The main purpose of buying the flat car is to transfer the plate and steel in the workshop. According to the actual situation of the site, the rail transfer car is recommended. The track needs to be laid first, and then the flat car transfers the goods.

A large-capacity battery trackless flat car with a load capacity of 50 tons. It is exported to India. The customer mainly provides solutions for the automotive industry. This project is suitable for the transportation of molds for auto parts, and is mainly used for mold handling in the workshop. . The flat car is used for trackless transfer, which can be used and stopped in the workshop.

The battery rail car is suitable for the factory. This flat car is exported to the United Arab Emirates. It is a standard 5 ton battery rail car. This project is mainly used to replace the unpowered rail car in the customer’s old factory. The battery is installed this time. Powered rail cars can save manpower and material resources while being more efficient.

Lithium battery-powered automated vehicles, the flat car weighs 6 tons, and the flat car has a remote control handle. The customer does industrial control automation engineering and uses transportation equipment. The customer installs equipment on the table, which is a magnetic stripe navigation. Safe and convenient.

With automatic navigation, it is suitable for the battery-powered transfer vehicle of the equipment factory. This agv trolley weighs2.5 tons. The customer is used for cremation equipment. It is mainly used to transport coffins. The vehicle is equipped with an automatic navigation system and battery-powered. Relatively safe and convenient.

The rail car used to transport structural parts in the workshop, the flat car weighs 10 tons, and the customer has opened a new structural part coating line project, which mainly transports large structural parts in the workshop and linear transportation, so the rail car is used. The flat car is equipped with a remote control handle, which is easy to operate and can control the operation of the flat car at any time, which is safe and efficient.

The rail car is suitable for the factory to handle raw materials. The maximum load capacity of the flat car is 10 tons. The customer is mainly used for transfer between workshops. The customer is a newly-built factory, which mainly transports raw materials. The power supply method uses cable reel power supply. the way.

It is used to transport steel battery-powered rail cars. The flat car weighs 40 tons. It is exported to Malaysia. The customer is mainly used to transport steel and other heavy materials. The flat car uses battery power supply, which can not be restricted by distance. More convenient.

The rail transfer car suitable for foundry industry to transport castings, the flat-car weighing 20 tons, is a product exported to Singapore. The customer does not need to add a transportation line to the newly built factory to transport the processed castings from the processing area to the warehouse.

A battery-powered railcar for transporting steel structure materials. The flat car weighs 60 tons and has a large load. This project is a cross-span transfer car used in the workshop. In the steel structure industry, customers are very strict with the structure of the trolley. The box beam structure used. Power storage and power supply, using DC motor, excellent starting performance.

It is a rail car suitable for steel coil transfer in workshops. The flat car has a load of 25 tons and uses an insulating pressure plate. The company purchases a rail car to transport the steel coil. The transportation before the two workshops uses a rail flat car. , Safe and efficient.

A rail transfer vehicle used to transfer steel bars and other materials. The flat vehicle weighs 5 tons. The platform of the trolley is customized according to customer requirements. It is powered by batteries. The customer’s special requirement is to have dual-control switching. The transfer vehicle is mainly used in the production workshop to complete semi-finished parts. Transfer operations.

It is a rail transfer car suitable for charging the battery of the workpiece in the transportation workshop. The flat car has a load of 10 tons. It is mainly used to transport equipment in the production workshop and transfer of the workpiece. The flat car is powered by a battery pack and is equipped with wired remote control handle and wireless remote control handle for two operation modes.

Low-voltage rail-powered transfer vehicles with remote control handles are used for workshop transfers. Rail flat cars with a load of 10 tons are mainly used for workshops and workshops. The power supply adopts rail low-voltage power supply. The car is equipped with a remote control handle, which can control the car’s forward and backward stop and start at any time.

Large-capacity rail cars suitable for various industries, flat cars with large-capacity loads, can carry materials with a load of 20 tons, suitable for various factory industries, and can greatly save manpower and material resources. The flat car can be customized according to customer needs, which is more comprehensive.

A rail transfer vehicle powered by a battery that can be operated. The vehicle is powered by a 48v battery. The working principle is: the battery provides electricity, and the motor drives the flat car to move. The Ouxing car is equipped with a handle on the car to control the flat car to move forward. , Backrest, stop, flat car adopts motor braking, the braking is stable, reliable, safe to use, and convenient for maintenance.

A transfer vehicle used to move metal structural parts on the track-the vehicle runs under heavy load, the maximum load capacity is 20 tons, and the track is laid in advance and runs on the track. It is mainly used to transport metal structural parts to the workshop, instead of forklifts.

The battery rail car used for material handling. This rail car has a load of 3 tons and the load is not very heavy. This rail car is mainly used for transporting metal structural parts in the workshop. It adopts the power supply and electromagnetic brake. Work with the crane in the workshop.

Battery-powered railcar with remote control handle. The trolley weighs 20 tons. It is mainly used to transport molds and boxes. The customer purchased 3 sets to use together, which can save material and manpower and improve efficiency. Equipped with a wireless remote control handle, it can control the flat car at any time. .

Rail trucks for large-capacity transportation of molds have a relatively large capacity and a heavier load, with a maximum load of 60 tons. They are mainly used for mold replacement. The molds are heavy and the driving is not safe. Rail cars are used to transport molds.

An electric rail transport vehicle for handling molds. The company mainly produces materials. The flat vehicle is purchased for mold replacement. The crane hoists the mold and puts it on the vehicle. The flat vehicle is transported to the designated location. The battery power supply method adopted by the car is environmentally friendly and energy-saving.

Suitable for battery-powered rail cars for heavy-load material handling. This rail car is exported to Latvia. It is a heavy-load flat car with a maximum load of 25 tons. It is mainly used for large-tonnage material handling and uses battery power supply.

It is suitable for large-scale factories to transport steel coil battery-powered rail cars, small cars weighing 200 tons and heavy loads. According to customer requirements and actual conditions, battery-powered rail cars are recommended. Customers are mainly used to transport various types of steel coils and steel.

A rail car suitable for handling cast parts in various manufacturing factories–this is a 5 ton rail car. The project company is mainly engaged in the manufacture of castings. Therefore, the rail car is mainly used to transport cast parts. Warehouse truck processing area.

A rail car suitable for the transportation of waste barrels in factories-the car is mainly used for the transportation of waste barrels. The environment is mainly in the spraying workshop. Because the workshop has paint, the flat car is explosion-proof, the electrical box is explosion-proof, and the wheels are made of stainless steel. Wheels.

Customized rail car used for material handling–This product is a 5 ton rail carrier, which is a customized product. Products of different tonnage sizes can be customized according to customer requirements. It is often used for material handling and is suitable for heavy industry enterprises.

Large-capacity platform transfer vehicle for material handling: This vehicle is mainly used for material handling in warehouses, instead of forklifts. The trolley has a relatively large carrying capacity and can carry 15 tons of materials for transfer back and forth between the warehouse and the workshop. The power mode adopts battery power supply, which can not be restricted by direction and distance.

A battery carrier truck suitable for moving molds in the factory workshop-the truck is mainly used to move back and forth in the workshop, and is mainly used for moving various molds. The battery is used for power supply, which is not restricted by the direction and is convenient and smart.

Turning car with lifting platform for the transportation of equipment workpieces: This customer is suitable for the transfer of amusement equipment workpieces, requiring a 30-degree turn, and can transport the equipment workpieces on the same height platform, so the platform of the turning car is added A lifting platform.

Suitable for large-capacity mold transfer vehicles in factories. This transfer vehicle is used by customers in Greece in the factory. Customers mainly produce various molds. This vehicle is mainly used to transfer molds. According to customer requirements, large-capacity loads- 20 tons, can be easily transferred in the factory.

The battery trackless trucks and trackless trucks used for material handling can be conveniently used in various places, and the table top is made into a half recess. Suitable for use on various stages. The truck is powered by a battery and is not limited by distance.

Battery-powered flatbed truck used for workshop transfer–The customer of this transfer truck requires a carrying weight of 3 tons. The transfer truck must carry an experimental box. The transfer truck pulls the experimental box to different stations for testing and use, so the transfer truck Can rotate 360 degrees. The car is equipped with a wireless remote control and a handle and a handle on the car, which can control the operation of the transfer car.

The battery-powered trackless truck for the transportation workshop equipment-the trackless truck weighs 5 tons and is used for the transportation of equipment in the disinfection workshop. The table size can be customized according to customer requirements. The power supply method: battery power supply.

A mobile platform vehicle powered by a special-shaped countertop battery–the trolley is made into a depression on the countertop according to the customer’s requirements. The trolley weighs 2.5 tons and is mainly used to transport rubber products. The trolley is a product developed by us and can be customized according to customer requirements. Customized, the car uses a battery to supply power to the power system, which is more flexible and convenient.

A large-capacity railcar suitable for handling heavy objects in factories—customers require that they can turn in multiple directions during transfer, so the design incorporates the function of 360-degree in-situ rotation. The load weight of the trolley is 20 tons according to customer requirements. , This kind of trolley is suitable for handling materials in various factories.

Used for cement floors, material handling vehicles with remote control-used by customers to move materials, materials, the ground has hardened into a cement place, and does not want to damage the ground here, so the use of trackless vehicles. The trolley is equipped with a wireless control handle and a joystick, and the trolley can be operated by operating the handle or the joystick.

Explosion-proof transfer vehicle used for steel pipe transportation in steel plants-the customer is a steel plant, which is mainly used to transport steel pipes of various sizes. Because the customer has requirements on site temperature, the motor uses an explosion-proof motor to ensure safety.

A heat-resistant and remote-controlled transfer vehicle used for heavy load transfer in factories–this trolley is mainly used by customers to transfer steel products from the processing area to the finished product area. The trolley is required to withstand high temperatures. The battery of the trolley uses explosion-proof and high-temperature resistant batteries ; The trolley load steel tonnage is relatively large, and the design is designed for a maximum load of 40 tons. The car is equipped with a remote control, which can operate the wireless remote control to control the trolley.

Handling truck used for factory metal materials, stamping dies and other materials—this trolley carries small tonnage materials and has a load of 5 tons. It is suitable for material handling in factory workshops and workshops. It is flexible and convenient to use, and comes and goes freely. The speed can be set according to the situation.

The new energy environmentally friendly trolley car used for multi-directional transfer in the factory workshop. According to customer requirements, it is mainly used for the transfer of molds and other equipment in the factory workshop. Environmental protection is required. Therefore, the battery power supply method is adopted. The trolley can be 360-degree multi-directional Transshipment is more convenient.

A battery-powered trackless transfer vehicle used for workshop transfer. This transfer vehicle uses lithium battery power to provide power to the trolley, and battery power is not limited by distance. The size of the table is customized according to customer requirements. The car is equipped with an alarm device. When the power is less than 30%, it will remind the user, and the power will be automatically cut off when the power is less than 20%.

A trackless transfer vehicle that rotates and transports molds in situ—The transfer vehicle is mainly used to transfer wind turbine fan blade molds and yacht parts molds, mainly indoor and outdoor transportation. Turning method: turning while walking, rotating at 30 degrees in place . Power supply: battery power supply.

A trackless platform vehicle suitable for handling steel structures. The customer is for container manufacturing and metal steel structure manufacturing. Customized trolleys are mainly used to transport steel structure materials. The main technical requirement is the distance of the table top from the ground.

A wireless remote control transfer vehicle powered by a concave battery-powered countertop-the trolley has a concave countertop. The power is powered by a lithium battery and is not limited by distance. The car is equipped with a wireless remote control that can control the trolley to start, stop, and run at any time.

For handling large-capacity trackless trucks, customers use trolleys to transport products with large-capacity objects and transfer them back and forth in the workshop. Because of the high frequency of use and forklifts cannot handle heavy objects, the customer uses trackless trucks. This vehicle is convenient, flexible and quick to transfer.